岗亭的应用当然都是在室外,但是在室外就难免会有各类的剐蹭划痕或者污渍,对于这种污渍我们应该如何去进行处理呢
一、划痕
集成岗亭厂家称岗亭为了防止工艺润滑剂或生成物、污物积留,必须对不锈钢岗亭划痕和其它粗糙表面进行机械清理。处理方式:我们可以进行磨粉添加或者手动磨平等技术来解决哦。
二、锈斑
在制作前或制作过程中有时会看到上海不锈钢岗亭产品或设备上生锈,这说明表面受到严重污染。处理方式:设备投入使用前必须把锈清除掉,彻底清理过的表面应通过铁试验或水试验进行检验。
三、油和油脂
有机物质如:油,油脂甚至指印都会成为局部腐蚀的腐蚀源。由于这些物质能起屏障作用,它们会影响化学和电化学清理效果,因而必须彻底清理掉。
四、残余粘合剂
撕掉胶带和保护纸时,粘合剂总有一部分残留在不锈钢表面。处理方式:1、当粘全剂还没硬化前,我们可以用有机熔剂去除。2、当粘全剂使用时间过久后,它就会形成硬化黏贴剂,形成缝隙腐蚀的腐蚀源。这样的话,我们需要用细磨料进行机械清理,这样可能要消耗很多的人力物力。
五、粉尘
岗亭的放置位置通常都会有粉尘,空气中常带有许多粉尘,它们不断地落在岗亭的表面。像治安岗亭、交通岗亭、小区岗亭、警务岗亭这种时常处于高人流的地方的岗亭,很容易就被粉尘所污染了。处理方法:我们可以用水或碱性溶液去除掉落在岗亭表面的粉尘。
Of course, the application of the sentry box is outside, but outside, there will inevitably be various kinds of scratches or stains, for this kind of stain, how should we deal with it? First, the scratch integrated booth manufacturers say that the booth in order to prevent the process lubricant or product, dirt accumulation, mechanical cleaning of stainless steel booth scratches and other rough surfaces is required. TREATMENT: We can add grinding or manual grinding leveling technology to solve Oh. Rust spots are sometimes seen on the products or equipment of the Shanghai stainless steel box before or during the production process, which indicates that the surface is seriously contaminated. TREATMENT: The rust must be removed before the equipment is put into use. Thoroughly cleaned surfaces should be tested by iron or water tests. 3. Oil and grease organic substances such as oil, grease, and even fingerprints can be sources of localized corrosion. As these substances can act as barriers, they can affect the chemical and electrochemical cleaning effect, so must be completely removed. When the adhesive tape and protective paper are removed, a part of the adhesive will remain on the surface of the stainless steel. Treatment: 1, when the whole adhesive has not hardened, we can use organic flux to remove. 2. When the whole adhesive is used for a long time, it will form a hardened adhesive and form a corrosion source of crevice corrosion. In this case, we need to use fine abrasives for mechanical cleaning, which may require a lot of manpower and material resources. Fifth, the location of the dust booth will usually have dust, often with a lot of dust in the air, they constantly fall on the surface of the booth. Like the Public Security Post, traffic post, community post, police post, such often in a high flow of places post, it is easy to be contaminated by dust. TREATMENT: We can use water or alkaline solution to remove the dust falling on the surface of the booth.
余杭区良渚街道安溪路7号